Did you know?

Oct 19, 2022 · How to install a replacement DFI Kit + Pinch Detect Terminals in the Litter-Robot 3. The DFI Circuit Board and brackets may appear different from what is pictured depending on when the unit was ... Cleaning the sensors. With the globe, bonnet, and drawer removed, lean the unit backward so that you can look into the holes on the bezel to see each sensor. Using a clean, dry cotton swab, carefully clean the surface of each sensor to remove any dust. It is important to note that it will be very difficult to see any dust, specifically on the ...To reset DFI sensor fault on a Connect Litter Robot please hold Reset button until the blue light blinks quickly. After that, it should come to solid blue light. This should really fix the issue of the DFI. 1 Like. Rutoy21 July 13, 2020, 4:53am 22. @pjutras yes ...So one day, out of the blue, the same issue happened with our Open Air III, all 3 lights blinking and nothing works. What happens is that after restart the yellow light stays on for like a couple of minutes, and then all 3 lights start flashing simultaneously. Over the course of next one month we changed: Bonet; Globe; DFI kit; Anti-pinch pins ...I’m trying the below based on what some other LRC users have said. Basically to improve/correct the data gathered by your litter robot you have to let it do its cycle once the cat has used it If you get a bin full notification, check the drawer. If it’s not full then press the reset button on the litter robot (not on the app) Repeat steps 1-2 until the bin is …late answered but here is how i fixed mine, but last time i take out the board to change the Full/empty sensor at the bottom Tray and re-assembly it back and my LR3 indicate the “Home Position Fault”. Turned out i didnt put the Hall effect sensor in the correct position. So make you u put it back like the one in the picture.Litter robot 3 stops mid cycle. I have had the litter robot air for 2 months and it was working fine but recently it has started to stop every few seconds during cycle. The yellow light flashes and cycle continues after 15 secs but then stops again and again even after the robot is returning to its home position.Hello, I have a problem with Litter Robot 3. It has blue flashing light at the beginning. I have tried everything (cleaning, reset, check dfi sensor and empty drawer) and when I plug back in it stuck at solid yellow light now (yellow light only). None of buttons is worked even the power button. Any help would be appreciatedLitter-Robot Cats Litter Box III 3 Open Air DFI Hardware. by Litter-Robot. Write a review. How customer reviews and ratings work See All Buying Options. 0 total ratings, 0 with reviews ...Our litter robot was Flashing Yellow Slow & Fast, then Fast Flashing Blue despite being empty and lastly just Random Lights. Watch for the solution to this, ...I concluded (before disassembly) that it was both the pinch sensor and the DFI assemble causing me trouble so in a Hail Mary I tried to fix both problems in one go. On my litter robot I found and removed 9 screws from the underside of the base to access the electronics within the base.LR3 DFI sensor replaced, still erroring Litter-Robot 3 Inherited a LR3 (not the connect version), gave it a thorough clean and it worked great for 2 weeks. Then got the error …Discover how to troubleshoot your Litter-Robot 4's Drawer Full Indicator (DFI) sensors on our support page. Click for step-by-step guidance now. ... Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels.Litter Robot 3 infrared Drawer Full Indicator circuit boards and assembly Kit for a blue flashing light issue. Kit includes DFI board assembly, DFI housing, mounting screws, …Litter Robot 3 not reversing during cycle. My Litter Robot 3 has been having a weird issue for the last two weeks. When it cycles, the globe rotates counter-clockwise until the hall sensor detects the magnet on the globe. It then stops, like it should. Then it's supposed to rotable clockwise to return to its home position, when the hall sensor ...With both options, you will get an additional warranty, just in case! -Base Replacement: This is a $399 replacement and gets you a new Litter-Robot base with a 1-year warranty. If your unit was purchased after Jan 1, 2020, you are eligible for a 50% discount on a replacement base at $199.50.Compatible with Litter-Robot 3 only. The Litter-Robot 3 Open Air DFI Hardware (v2) is a replacement DFI Hardware for your Litter-Robot 3. It is compatible with Litter-Robot 3 only. What's Included. 1x Litter-Robot 3 Open Air DFI Hardware (v2) Specifications. Compatible with Litter-Robot 3 only.Check for obstructions. Check for obstructions that might prevent the cat sensor from functioning. Make sure Litter-Robot is on a firm, level surface. The cat sensor function can be affected if the unit is on carpeting or a litter mat. Check that there are no power cords running underneath the base of the robot that might obstruct movement.

1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will …You can try to clean the 2 green circuit boards and the 2 plastic brackets of the DFI sensor using isopropyl alcohol and a Q-Tip to remove any rust or dust from them. If that didn’t help, the DFI sensor will have to be replaced first in order to make the robot functional again. Let us know if there’s anything else we could assist you with.The issue that you are having would require replacing the DFI sensor and the 3 sets of pins so you can order the following parts from the following links: RobotShop Europe Litter-Robot 3 Open Air DFI Hardware (v2) Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 ...Hi all, I'm having an issue with my 1 year old litter robot 3 where after every use the app says drawer full and the blue light flashes. I've followed all the litter robot troubleshooting steps including cleaning the lense and re-calibrating the sensor. I've created two support tickets and have been waiting over two weeks for a response from ...

Note: This problem is EXACTLY the same as this other post I found, which is why I’ve essentially just copied the description from there: Litter Robot Cannot Find Dump Position. Hardware concerned: Litter Robot III Connect. Software concerned: N/A. Troubleshooting steps already taken: unplugging it and plugging it in again; cleaning the …If it cannot cycle after three attempts, the globe will return to the home position, and the control panel will flash yellow and red or blue and red lights. There are a few things you can do to troubleshoot a jammed Litter-Robot globe: 1. Turn off the unit and unplug it. 2. Remove the bonnet. 3. Remove the globe. 4.Litter-Robot Cats Litter Box III 3 Open Air DFI Hardware. by Litter-Robot. Write a review. How customer reviews and ratings work See All Buying Options. 0 total ratings, 0 with reviews ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. BEFORE DOING THIS BYPASS HACK:Be sure to do the usual fixes first.. C. Possible cause: 3. Brush out excess litter. If any litter remains in the robot, brush it awa.