Did you know?

Removing the bonnet, flexing/bending back the latches (I discovered I wasn't properly seating the back clasps in-place, this helped a bit with the jerky spinning but failed to …My LR3 seems to still be doing the proper cycles and such, but I can't control the robot from the app, and the level isn't updating (in the app) from the percentage it was last at before I stopped getting notifications (even after changing the litter and doing a reset). 2. o-Valar-Morghulis-o. • 6 mo. ago.Litter-Robot is equipped with anti-pinch sensors on both sides of the waste drawer chute to ensure your cat’s safety while in use. These sensors monitor for potential pinch …Litter robot 3 safety bar detected flashing yellow light. Im trouble shooting my litter robot since it stopped upside down and says safety bar detected. It’s asking me to check if my pinch terminals are touching and free of obstruction…. There is a ton of waste build up on those pinch detectors. I would start by using a small head ... Litter Robot owner here -- Have had two litter robots and I think a recent batch of circuits is faulty. First one had no trouble with DFI for years; second one I bought refurbished and DFI went in 2 months. I replaced the DFI on first one, that lasted only 2 months. If Whisker does not get on top of this, they will lose their audience.Turn off the Litter-Robot and unplug it from the power source. Remove the waste drawer and the bonnet. Locate the sensor calibration button, which is located on the control panel near the power button. Press and hold the sensor calibration button, and at the same time, plug the Litter-Robot back into the power source. Litter-Robot 4: Light Codes Guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more.If you have a Litter-Robot III Open Air 3 and it's stopped working with yellow blinking / flashing light and/or the globe does not rotate in normal ... With this type of yellow light error, ... this blinking yellow light as shown in our video is because of the anti-pinch safety feature malfunctioned or became defective. Basically, ...Ensure your cat did not enter Litter-Robot during the clean cycle. If your cat did enter, please press the reset button after use. Ensure the litter level doesn’t exceed the raised fill line. If there is too much litter, please remove enough to meet the fill line. Inspect bonnet tabs for corrosion or debris. Remove debris or corrosion if evident.I would definitely recommend calling the Litter Robot support team - they were really helpful when I called with frequent cat sensor faults a few months after getting our litter robot 3 - they recommended filling it less than I have been - suggesting it may do better 1/2" or 1" BELOW the fill line - apparently with different weights of litters, they've found filling up to …The Litter-Robot 4 has a cooler and more straightforward design that fits well in most homes. As time goes on, there’s usually more cat litter that ends up around the unit. Materially, in the case of Litter Robot 3 vs 4, the Litter-Robot 4 is a bit better because it’s smoother and has fewer parts to wipe down.Litter-Robot is equipped with anti-pinch sensors on both sides of the waste drawer chute to ensure your cat’s safety while in use. These sensors monitor for potential pinch conditions at all times. If your unit displays a green and white alternating light bar, this indicates an anti-pinch fault during power up.Tips and tricks for litter robot (pinch detect hack) Gives good tips. Also a very useful mod to protect pinch detect sensor. Final thing I’ll say, petroleum jelly on the metal connector for the pinch detect to help prevent corrosion. Mods, if you see this post please pin for future users to see. This is super useful! Disassemble. 1. Turn the base over so it is upside down. 2. Remove the 9 screws connecting the bottom of the base to the top of the base. 1 screw at the back of the unit behind the black cat sensor foot. 3. Gently lift to separate the two halves of the base. The pieces will still be connected by a wire.About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket …Stops one of the most annoying problem when the robot gets stuck and does not unstuck by itself.In my personal opinion, this sensor is an overkill for the pr...

Also read: Beyond Litter Disposal: Dealing with Pinch Detect Fault Litter Robot. Yellow Ping-Pong: Meaning: A light pattern resembling a moving ping-pong ball signifies the activation of the pinch detector for your cat’s safety. Solution: Look into the Waste Drawer for any foreign objects possibly triggering the sensors.Preparation. Litter-Robot is equipped with the SafeCat system that uses the cat presence motion sensor to detect motion in the waste drawer. If your unit displays a red ping-pong light bar, this indicates that motion was detected in the waste drawer and the globe will cycle to the Dump position to allow the object to escape. If you need to replace the pinch detect terminals on your Litter-Robot and the unit is out of warranty, the process is simple and quick. For those who are th...As of now, my litter robot will refuse to cycle or empty while flashing the same yellow light over and over. I checked the waste drawer and anything in that area, to which there is nothing seemingly wrong there. Although roughly 4 weeks ago, it was terribly packed into the U Haul which broke the litter robot (globe and bonnet popped out).I’ve tried various litters, unscented, cat attract, regular litter box in different shapes, sizes, unclumping litter, pelleted litter, etc. He’ll use a puppy pad until it’s dirty, then the floor. ‍♀️ I thought this was a permanent issue, but I boarded him while we were gone a weekend and he used the box, not the pad, every.

So, whisker devs FIX THE APP or ill hack you and do it myself. Go line by line in your code and use a note book or white board to explain each function in words like: this is what makes the app UI, this is for when the robot sees an error, etc. You will find the faulty code and then you can fix it. Okay? Okay. Thank you.The Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three laser sensors located in the top of the ... …

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Community for all things Litter-Robot. Post your experienc. Possible cause: Skip to main content. Open menu Open navigation Go to Reddit Home Open .